Hello, can I use some node for mpu6050 (board gy521)? I try to use this https://xod.io/libs/gabbapeople/mbot-lib/ , but it doesn’t work. I can’t find and do this step : “To add an Arduino library open the place where XOD is installed and copy the library folder to packages/xod-client-electron folder…

Hi! Could you please describe the error that occurs during the upload in detail. Even better to attach the upload log with the error or to attach a screenshot. Thank you.

I really don’t know what is wrong. [V%C3%BDst%C5%99i%C5%BEek]

I’ve updated the mbot-lib =) Ok, here are things for you to do: Make sure you have the latest IDE version, if it is not latest then update. Update the lib. Go to $HOME/xod/__lib__ and delete the gabbapeople/mbot-lib library. Add the new version 1.2.3 of the gabbapeople/mbot-lib using the XOD …

Thank you, now it works great. It’s good information for others. My problem was, that i didn’t copy the I2Cdev and MPU6050 to ardulib. I have another question: is it possible to use this library (mbot-lib) without Mbot board (I using A. UNO)? Just for reading the sensor? Because, primary I am looki…

Mcore Board is almost analogy of Arduino Uno. So Yes, you can use Uno. Note: In this library, for the proper “MPU6050” node operation, it is better to use the INT pin. A “gy521” board that you have has this pin, so don’t forget to attach it. Also, calibrate the sensor before use as it is written…

Great, now with INT it works perfectly. For calibrating I have used this (I hope, that it is correct):[V%C3%BDst%C5%99i%C5%BEek]

Hello ! How did you connect the Gy-521 with the Arduino ? And how do you tell to the node which port you used ? INT pin is the only port showed in the node. EDIT : I suppose you have to plug the SDA and SCL in the corresponding Arduino port, but I have no output on watch node, any idee ? (I’m on 0.…

I’ve done some test and apparently, the mpu6050-calibrate node and the mpu6050-yrp-linear-accel node break XOD IDE. Nothing in the code works when they’re used (test led does’t receive input, console log and watch nodes don’t work, …). Any idee how to solve the problem ?

Hi Vanilord, if You ask about hardware I did it last night with 1 x RJ25 6p6C female connector 1 x flat 6 wire x 0.25mm2 cable (only 5 cm long) 1x GY-521. Some schematic and one photo may be enough to get a clue how to make it. [GY-521%20to%20mBot%20] Regarding XOD I am real rocky but it is…

Thanks for the reply. My setup is quite basic. I’ve added the AD0 pin, but I still have no result. [Capture] [IMG_20190210_160721] [IMG_20190210_160742]

Library for Mpu 6050 (gy-521)

Hardware Interfacing Questions

cesars July 27, 2019, 9:01pm 17

could this be

Topic		Replies	Views
Error while uploading mpu 6050 chipset program in arduino Uncategorized	1	766	September 14, 2020
MPU 6050 / Gy-521 - Help (solved) Uncategorized	4	1641	February 8, 2019
Gabbapeople/mpu6050 library Install/Upload Problems	2	1683	June 16, 2022
Getting error while calibrating MPU6050 Uncategorized	10	1197	April 4, 2019
MPU6050 - doesn't detect any movement Hardware Interfacing Questions	4	1585	November 30, 2019

Library for Mpu 6050 (gy-521)

Related topics