# Dht11-hygrometer error

**URL:** <https://forum.xod.io/t/dht11-hygrometer-error/3570>\
**Category:** XOD Programming Questions\
**Created:** [February 29, 2020, 1:49pm UTC](https://forum.xod.io/t/dht11-hygrometer-error/3570 "2020-02-29T13:49:01Z")\
**Posts on this page:** 8\
**Page:** 1

<div class="post-metadata">

**Author:** ![kadetsr](https://avatars.discourse-cdn.com/v4/letter/k/41988e/32.png) [@kadetsr](https://forum.xod.io/u/kadetsr)\
**Post date:** [February 29, 2020, 1:49pm UTC](https://forum.xod.io/t/dht11-hygrometer-error/3570/1 "2020-02-29T13:49:01Z")

</div>

Hello XOD Community

I have a dht11-hygrometer and I installed the library for it xod-dev/dht I have an UNO and the dht11 output pin is connected to pin 10, + to 5v and - to gnd. When I upload to the UNO I get the following message  
=== Debug session started ===  
RR:523:7:31  
XOD\_ERR:121:7:31 code

I have two watch nodes attached one to Tc and one to RH they will flash between ERR and very briefly a number Tc 25.0 and RH 34 which I interpret are the Temp and humidity respectively temp is in C.

The dht11-hygrometer node perimeter box turns red and the text in the watch nodes is also red.

 ![Screenshot from 2020-02-29 07.46.50](https://canada1.discourse-cdn.com/flex027/uploads/xod/original/2X/a/a307bfb29e11979f08ea3c3225f23ddebfb0ca58.png)

Thanks

Kadetsr

---

<div class="post-metadata">

**Author:** ![gweimer](https://avatars.discourse-cdn.com/v4/letter/g/a9adbd/32.png) [@gweimer](https://forum.xod.io/u/gweimer)\
**Post date:** [February 29, 2020, 5:53pm UTC](https://forum.xod.io/t/dht11-hygrometer-error/3570/2 "2020-02-29T17:53:21Z")

</div>

Some sensors need time to recover between checks you could try connecting clock to the UPD pin to update every second instead of setting it to loop.

---

<div class="post-metadata">

**Author:** ![kadetsr](https://avatars.discourse-cdn.com/v4/letter/k/41988e/32.png) [@kadetsr](https://forum.xod.io/u/kadetsr)\
**Post date:** [February 29, 2020, 7:33pm UTC](https://forum.xod.io/t/dht11-hygrometer-error/3570/3 "2020-02-29T19:33:04Z")

</div>

when I added the clock it would alternate flashing with ERR and the dht node boarder in red for 1 second and then white with the actual temp and RH for 1 second. clock IVAL is 1.

I placed the sensor in my hand and then the ERR stopped and the readings changed. Then I put the sensor down and after a bit the ERR began again.

I added a count node and linked it to the clock node with a watch. changed the clock IVAL to 10 and NO ERR. In my mixing station I want to record the outside temp & RH every time a batch is made. I also want to record the temp & RH every 15 minutes, this will give me an idea of how much solution is being consumed by the plants during various times of the day.

I purchased a “Geekstory Micro SD Card Module Mini TF Card Adapter Reader Module and Write Module with SPI Interface Driver Module + 40pcs Female to Male Dupont Cable Line for Arduino (Pack of 5pcs with Cables)” from amazon so far not able to get it to work any suggestions where I can read up on making this work in XOD.

Thanks  
Kadetsr

---

<div class="post-metadata">

**Author:** ![cesars](https://avatars.discourse-cdn.com/v4/letter/c/f05b48/32.png) [@cesars](https://forum.xod.io/u/cesars)\
**Post date:** [February 29, 2020, 8:30pm UTC](https://forum.xod.io/t/dht11-hygrometer-error/3570/4 "2020-02-29T20:30:46Z")

</div>

Have you connected the 10k resistor?

---

<div class="post-metadata">

**Author:** ![kadetsr](https://avatars.discourse-cdn.com/v4/letter/k/41988e/32.png) [@kadetsr](https://forum.xod.io/u/kadetsr)\
**Post date:** [February 29, 2020, 9:41pm UTC](https://forum.xod.io/t/dht11-hygrometer-error/3570/5 "2020-02-29T21:41:54Z")

</div>

no. Didn’t know that it needed one for a dht11.

Where does it go? Between the output and the Arduino?

Thanks  
Kadetsr

---

<div class="post-metadata">

**Author:** ![cesars](https://avatars.discourse-cdn.com/v4/letter/c/f05b48/32.png) [@cesars](https://forum.xod.io/u/cesars)\
**Post date:** [February 29, 2020, 9:47pm UTC](https://forum.xod.io/t/dht11-hygrometer-error/3570/6 "2020-02-29T21:47:19Z")

</div>

if the input does not have pull-up I think it needs it, it goes in vcc and data pin a 10k resistor

---

<div class="post-metadata">

**Author:** ![kadetsr](https://avatars.discourse-cdn.com/v4/letter/k/41988e/32.png) [@kadetsr](https://forum.xod.io/u/kadetsr)\
**Post date:** [February 29, 2020, 9:52pm UTC](https://forum.xod.io/t/dht11-hygrometer-error/3570/7 "2020-02-29T21:52:22Z")

</div>

I will try that

Thanks  
Kadetsr

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex027/uploads/xod/original/1X/eb7348baa04192c2ef932d1db54d44f09f8a7888.png) [@system](https://forum.xod.io/u/system)\
**Post date:** [May 4, 2020, 5:06am UTC](https://forum.xod.io/t/dht11-hygrometer-error/3570/8 "2020-05-04T05:06:09Z")

</div>

Closed on May 4, 2020, 5:06am UTC

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.
